BOLT MOUNTING KIT - Skates U.S.

Mounting Hardware Kit (Fixing Kit) Part Number:   STMSS The Roll-Line Mounting Hardware Kit is the little bag with the Hardware to properly mount your Roll-Line Skates to most any Skating Boot. Note that this kit is not included with any Roll-Line plates, and must be purchased separately if needed. The Roll-Line Kit Includes: Four (4) Long Mounting Bolts for the Heels Eight (8) Short Mounting Bolts for the Ball of the Boots Twelve (12) Flat Washers Twelve (12) Nuts that utilize a 7mm Wrench (This same kit can be used to mount ATLAS, Snyder, or most other Frames (including Inline Frames) to most Skating Boots.) The Mounting Hardware Kit (Fixing Kit) should be used with an 11/64″ Drill Bit and a Countersink when drilling your Skating Boots. Please follow the instructions in the Learning Center at www.. The Mounting Slide Show will provide step by step instructions on the best way to mount Skates and Frames together. On Today’s Skating Boots, it is strongly recommended to NOT use the Snyder Boot marking tool, as this will in most cases move the Toe of the Frame too far to the outside of the boot. It is strongly recommended to use all Four (4) of the Mounting Hardware Kit (Fixing Kit) Short Bolts, Washers, and Nuts and the EDEA Power Wedges in the Ball area of both Skating Boots, if they do not have the NEW Planar Roller Sole. All Traditional Leather Skating Boots should utilize Power Wedges.  Be sure to tighten all of the Mounting Nuts and even consider using a touch of Blue, Removable Lock Tite. Then use the  Bolt Break-Off tool to get that clean mount. All of these items are available from  .
Mounting Hardware Kit (Fixing Kit) Part Number:   STMSS The Roll-Line Mounting Hardware Kit is the little bag with the Hardware to properly mount your Roll-Line Skates to most any Skating Boot. Note that this kit is not included with any Roll-Line plates, and must be purchased separately if needed. The Roll-Line Kit Includes: Four (4) Long Mounting Bolts for the Heels Eight (8) Short Mounting Bolts for the Ball of the Boots Twelve (12) Flat Washers Twelve (12) Nuts that utilize a 7mm Wrench (This same kit can be used to mount ATLAS, Snyder, or most other Frames (including Inline Frames) to most Skating Boots.) The Mounting Hardware Kit (Fixing Kit) should be used with an 11/64″ Drill Bit and a Countersink when drilling your Skating Boots. Please follow the instructions in the Learning Center at www.. The Mounting Slide Show will provide step by step instructions on the best way to mount Skates and Frames together. On Today’s Skating Boots, it is strongly recommended to NOT use the Snyder Boot marking tool, as this will in most cases move the Toe of the Frame too far to the outside of the boot. It is strongly recommended to use all Four (4) of the Mounting Hardware Kit (Fixing Kit) Short Bolts, Washers, and Nuts and the EDEA Power Wedges in the Ball area of both Skating Boots, if they do not have the NEW Planar Roller Sole. All Traditional Leather Skating Boots should utilize Power Wedges.  Be sure to tighten all of the Mounting Nuts and even consider using a touch of Blue, Removable Lock Tite. Then use the  Bolt Break-Off tool to get that clean mount. All of these items are available from  .

All threaded rod, U-bolts, Channel nuts

Sold as a single bolt and a single washer

Wizard Frame Mounting Bolt and Washer

2000-lb. Winch Kit - Champion Power Equipment

Mounting Hardware - Derby Warehouse

Types of Bolts: Types, Components, and Fastener Terms

Ironman 4x4 America - Shopping Cart

Rad Pad Systems – Skate and Annoy Galleries

Mounting Hardware Kit

Bolts & Hardware For Inline Skates – Loco Skates

Skate Hardware - Find the Ultimate Roller Skate Mounting Kit

Methods for Joining Laser Cut Parts

Hello! I have various mounting kit options, aiming to cover all your skate mounting needs. We have *short bolts* which are the perfect length for most

Roller Skate Mounting Kit

How to Build A Fully Custom Roller Skate